Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Exactly How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We have stumbled on this article about A Step-by-Step Guide to Installing a Bathtub directly below on the net and concluded it made sense to write about it with you on my blog.
Setting up a bathtub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging project. If the old tub is readily obtainable, the job can move immediately; if you have to open up a wall to get rid of the old tub and place the new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and fit trying it. As opposed to hiring a service provider to take over a halfway-completed project, it is far better to consider utilizing one before you start. Possibilities are you might need a specialist plumber to make tube connections.
This write-up will aid you set up a brand-new tub in your bathroom if you have actually already acquired a new bathtub and don't require to change the arrangement of your previous water system pipelines.
Your tools as well as product checklist must comprise the following:
Preparing for the Setup
To start with, the sustaining frame supplied with the bathroom should be fitted (if required) according to the maker's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to moving on to fit the new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wood boards under its feet, put the bathtub in the needed position. The wood boards are helpful in uniformly spreading the weight of the tub over the location of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the spirit level reviews level.
To install faucets, fit all-time low of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; after that do the same for the various other tap.
Activate the supply of water and examine all joints as well as new pipework for leakages and also tighten them if required. Fill the bath tub as well as also examine the overflow outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub should wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. Once the tap is securely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The former type needs to be attached to the faucet ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, causing issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can break rather very early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate reader about Tools You Need to Install a New Bathtub , I assumed sharing that excerpt was a good thing. Do you know anybody else who is enthusiastic about the topic? Please feel free to share it. I treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
Details Here Report this page